Submit manuscript...
MOJ
eISSN: 2574-819X

Bioorganic & Organic Chemistry

Research Article Volume 2 Issue 3

Metal-free organic dyes derived from phenothiazine for dye sensitized solar cells; tuning of the performances by imidazole derivative

Sambathkumar S,1,2 Priyadharshini S,2 Saritha A,1 Renganathan R2

1Department of Chemistry, Theivanai Ammal College for Women (Autonomous), India
2School of Chemistry, Bharathidasan University, India

Correspondence: Sambathkumar Subramaniyan, Department of Chemistry ,Theivanai Ammal College for Women (Autonomous), Villupuram 605 401, India, Tel +9199 9413 4304

Received: December 13, 2017 | Published: May 18, 2018

Citation: Sambathkumara S, Priyadharshinib S, Saritha A, et al. Metal-free organic dyes derived from phenothiazine for dye sensitized solar cells; tuning of the performances by imidazole derivative. MOJ Biorg Org Chem. 2018;2(3):127-131. DOI: 10.15406/mojboc.2018.02.00067

Download PDF

Abstract

Three imidazole - triphenylamine based organic dyes (SS PI1, SS PI2 and SS PI3) configured with donor –donor – π spacer – acceptor (D-D-π-A) structures were synthesized with different acceptor units. The optical and electrochemical performances of the dyes were analyzed carefully. Based on the analysis on the performance of the synthezied dyes towards the application of DSC are which has been suggested as an accountable for greater DSC’s efficiency. So, this new molecular design could trigger the future development of other simple organic photosensitizers for efficient DSC’s which support the sustainability of the modern society.

Keywords: dyes sensitized solar cells, phenothiazine, acceptor, efficiency, sustainability

Introduction

Exclusively organic dyes continue to capture the attention of scientific community devoted to the development of dye sensitized solar cells as a competitive alternative to ruthenium based complexes.1 Many organic dyes based on the push-pull structure of donor - conjugated linker-acceptor system, which exhibit relatively high DSC performances have already been designed and developed.2‒5 Organic dyes can be divided into two categories, one containing triarylamine donors while the others have heterocyclic donors. The electron rich nature of phenothiazine moiety provides a good relay for the electron migration from donor to acceptor, which can induce an efficient intramolecular charge transfer (ICT). Phenothiazine has electron rich sulfur and nitrogen heteroatom, and its ring is non-planar with butterfly conformation in the ground state, which can impede the molecular aggregation and the formation of molecular excimers. The additional electron rich sulfur atom renders phenothiazine a strong donor than other amines, even better than tetrahydroquinoline and carbazole.6‒8

Meanwhile the 10-substitution of N can further enhance the charge separation at the oxide solution surface. Moreover, the two phenyl groups are arranged in a small torsion angle related to N (10) and S (9) atoms, so that π – delocalization can be extended over the entire chromophores. In addition, the electronic properties and the structural diversity can be enhanced by the attachments of auxiliary chromophores to the amine unit.9‒13 Fine - tuning of the frontier molecular orbital energies are required to achieve efficient electron injection from the dye into the conduction band of TiO2 and facile regeneration of the oxidized dyes by a redox couple. Likewise, organic dyes with D-D-π-A structure can achieve the enhanced photovoltaic performance via the modification of molecular structure compared with D- π-A structure.14‒19

Introducing an imidazole derivative as an additional donor to the D-π-A structure is a possible alternative to retard the interfacial charge recombination dynamics and to retain efficient light-induced charge separation and lead to extend π–conjugation of the chromophores.20,21 Therefore, taking all the above mentioned points in to consideration, we designed and developed D-D-π-A structured metal free organic dyes consisting of phenothiazine as donor and π-spacer1a, an imidazole derivative as additional donor and different electron withdrawing anchoring groups (cyanoacetic acid,22 nitrophenyl acetonitrile23‒26 and rhodanine acetic acid27). The newly synthesized dyes are characterized by NMR and FT-IR spectral analysis. Further, their absorption, emission and electrochemical behavior were carefully analyzed. The molecular structure of the three dyes, namely SS PI1, SS PI2 and SS PI3 are displayed in Figure 1.

Figure 1 Molecular structure of the synthesized dyes.

Experimental part

Synthetic procedures

General procedure for the synthesis of 10-propyl-10H-phenothiazine (S1); N – alkylation: A dimethyl sulfoxide (DMSO) solution of phenothiazine (2) (0.5mmol) was allowed to stirred for 30 min. with sodium hydroxide (NaOH) (0.1 mol) at room temperature. To this, propyl bromide (0. 5 mmol) was added drop wise and the mixture was stirred at room temperature for 17hours. The mixture was quenched with water and extracted with ethyl acetate (EtOAc), washed with water, dried in vacuum and the compound was purified by column chromatography (silica gel 60-120 mesh, hexane/EtOAc) (5:0.5 v/v) as an eluent to afford the compound (S1) as a white solid.

 Yield: 85%, 1H NMR (400MHz, CDCl3, ppm): δH 1.0 (t, 3H, 7.6 Hz), 1.8 (m, 2H), 3.8 (t, 2H, 7.2 Hz), 6.8 – 6.9 (m, 4H), 7.1 (m, 4H), 13C NMR (400MHz, CDCl3, ppm): δ 145.36, 127.45, 127.19, 124.96, 124.35, 115.45, 49.15, 20.19,11.39, IR (KBr Pellet, cm-1): 3461, 2967, 2856, 1907, 1675, 1587, 1462, 1127,1026, 831

General procedure for the synthesis of 10-propyl-10h-phenothiazine-3,7-dicarbaldehyde (S2) ;vilsmeier - haack formylation: A mixture of DMF (0.1mol) and POCl3 (4mmol) in 2ml of 1, 2-dichloroethane (DCE) were allowed to cool for 0°C and stirred for 30min. To this, phenothiazine (2) (0. 4mmol) in DCE (3ml) was added and the mixture was stirred at 100°C for 8hours. The mixture was quenched with ice cooled water and filtered, washed with water, dried in vacuum and the compound was purified by column chromatography (silica gel 60-120 mesh, hexane/EtOAc) (5:1 v/v) as an eluent to afford the compound (S2) as a orange solid.

 Yield: 76%, 1H NMR (400MHz, CDCl3, ppm): δH 1.0 (t, 3H, 8.4 Hz), 1.8 (m, 2H), 3.8 - 3.9 (t, 2H, 7.6 Hz), 6.9 (m, 2H), 7.5 – 7.6 (m, 4H), 9.8 (s, 2H), 13C NMR (400MHz, CDCl3, ppm): δ 189.89, 148.90, 131.99, 130.18, 128.41, 124.42, 115.62, 50.19, 29.99,11.12, IR (KBr Pellet, cm-1): 3424, 2961, 2602, 1670, 1487, 1353, 1201, 1104, 914.

General procedure for the synthesis of 7-(4,5-diphenyl-1H-imidazol-2-yl)-10-propyl-10H-phenothiazine-3-carbaldehyde (S3); cyclocondensation: Acetic acid solution of 1, 2-diphenylethane-1,2-dione (0.5mmol), compound S2 (0.05mmol) and ammonium acetate (8.07mmol) were charged sequentially in a double necked round bottom flask and allowed to reflux at 105°C for 18hours. The mixture was quenched with ice and filtered, washed with water, dried in vacuum and the compound was purified by column chromatography (silica gel 60-120 mesh, dichloromethane/EtOAc) (50:1 v/v) as an eluent to afford the compound (S3) as a yellowish orange solid.

 Yield: 62%, mp: 154-156°C, 1H NMR (400MHz, DMSO d6, ppm): δH 1.0 (t, 3H, 7.6 Hz), 1.8 (m, 2H), 4.0 (t, 2H, 7.2 Hz), 7.3–7.7 (m, 16H), 9.8 (s, 1H), 12.6 (s, 1H), IR (KBr Pellet, cm-1): 3428, 3037, 2954, 1650, 1467, 1367, 1176, 769

General procedure for the synthesis of SS PI1, SS PI2 and SS PI3; knoevenagel condensation: A CHCl3 solution of P2 (0.1mmol, 0.2mmol and 0.5mmol with respect to SS PI1, SS PI2 and SS PI3) and cyanoacetic acid (0.2mmol for SS PI1), 4-nitrophenylacetonitrile (0.2 mmol for SS PI2) and rhodanine-3-acetic acid (0.6 mmol for SS PI3) (2mmol) with 0.1 ml of piperidine were allowed to reflux at 70°C for 4hours.

 The reaction mixture was extracted with CHCl3 and filtered, washed with water, dried in vacuum and the compound was purified by column chromatography (silica gel 60-120 mesh, dichloromethane/ethanol) (6:1v/v) as a eluent to afford the title compounds SS PI1, SS PI2 and SS PI3 as deep yellow solid, brownish red solid and pale red solid respectively.

2-Cyano-3-[7-(4,5-diphenyl-1H-imidazol-2-yl)-10-propyl-10H-phenothiazin-3-yl]-acrylic acid; (SS PI1): Yield: 48%, mp: 258-260°C, 1H NMR (400MHz, CDCl3, ppm): δH 1.8 (t, 3H, 5.2 Hz), 3.2 (m, 2H), 3.4 (t, 2H, 6.0 Hz), 6.8 (s, 1H), 7.3 -7.4 (m, 6H), 7.5-7.6 (m, 10H), 8.0 (s, 1H), IR (KBr Pellet, cm-1): 3421, 2951, 2834, 2235, 16224, 1461, 1350, 1252, 946, 771

3-[7-(4,5-diphenyl-1H-imidazol-2-yl)-10-propyl-10H-phenothiazin-3-yl]-2-(4-nitro-phenyl)-acrylonitrile; (SS PI2): Yield: 62%, mp: 230-232°C, 1H NMR (400MHz, CDCl3, ppm): δH 1.8 (t, 3H, 22 Hz), 3.7 (m, 2H), 3.9 (t, 2H, 7.2 Hz), 6.9 (m, 3H), 7.3-7.5 (m, 3H), 7.5-7.7 (m, 7H), 7.8–7.9 (m, 5H), 8.2 (m, 3H), IR (KBr Pellet, cm-1): 3395, 3065, 2939, 2855, 2205, 1561, 1493, 1334, 1113, 862, 694

 5-[7-(4,5-diphenyl-1H-imidazol-2-yl)-10-propyl-10H-phenothiazin-3-ylmethylene]-4-oxo-2-thioxo-thiazolidin-3-yl}-acetic acid; (SS PI3): Yield: 54%, mp: 168 - 170°C, 1H NMR (400MHz, CDCl3, ppm): δH 1.8 (t, 3H, 34 Hz), 3.3 (m, 2H), 3.5 (t, 2H, 9.2 Hz), 6.8 (s, 1H), 6.9 -7.0 (m, 2H), 7.3 - 7.4 (m, 3H), 7.4 (m, 3H), 7.4 -7.8 (m, 8H, ) 7.6 (s, 1H), IR (KBr Pellet, cm-1): 3412, 2937, 2832, 2722, 2523, 1641, 1471, 1373, 1192, 1106, 1015, 690.

Results and discussion

Synthesis and characterization

The synthesis of three new imidazole - phenothiazine based donor - donor -π-acceptor dyes are accomplish as shown in Figure 2. The structures of the synthesized dyes (coded as SS P11, SS PI2 and SS PI3) are given in Figure 1.

The synthetic pathways for the dyes involved stepwise protocol. First, the compounds S1 and S2 were prepared according to the reported procedure6,7b from compound 2 based on N –alkylation and Vilsmeier - Haack formylation, respectively. Then, 1, 2 -diphenylethane-1, 2-dione reacts with S2 and ammonium acetate in the acetic acid, which gave the corresponding compound S3 via cyclocondensation reaction.

Finally, the compound S3 with two fold excess of active methylene compounds (Cyanoacetic acid, Nitrophenyl acetonitrile and Rhodanine acetic acid) afforded the target dyes (SS PI1, SS PI2 and SS PI3) in chloroform with piperidine as catalyst using Knoevenagel condensation reaction. The structure of intermediates and the dye molecules were characterized by 1HNMR, 13CNMR and FT-IR spectroscopic techniques (included in appendix II). The difference in the three dyes is majorly related to the acceptor part, which has variation in electron withdrawing nature, where the anchoring of TiO2 occurs.

Figure 2 (A) Propyl bromide, NaOH, DMSO. (B) Phosphorous oxychloride, N,N- Dimethylformamide, 1,2 -Dichloroethane, reflux 90°C, 12hr. (C) Benzil, Ammonium acetate, Acetic acid, reflux 105°C, 28hr. (D) Active Methylene Compound, Chloroform, Piperidine, reflux 105°C, 4hr.

SS PI1 (R =Cyanoacetic acid), SS PI2 (R= 4-Nitrophenyl acetonitrile), SS PI3 (R= Rhodanine-3- acetic acid).

Optical properties

Generally, as the function of light harvesting, the dye plays a significant role for the DSC’s achieving high conversion efficiency and the absorption spectra of the dye could affect the device performance dramatically.20 Figure 3. shows the UV/Visible absorption spectra of the synthesized dyes SS PI1, SS PI2 and SS PI3 in dichloromethane solution and the corresponding data are summarized in Table 1. All dyes exhibited two distinct bands, appearing below 400 nm and around 400-510 nm respectively. The band located at a shorter wavelength (band 1) is attributed to an aromatic π –π* transition, and the band at a longer wavelength (band 2) is assigned to an intramolecular charge transfer (ICT) transition with the character of π –π* transition from the phenothiazine donor consisting of auxiliary chromophores to the electron withdrawing anchoring group.28‒30

Dyes

λabs/nm
(
ε / M-1cm-1)a

λem (nm)b

EHOMO (V)c

ELUMO (V)d

Eg(eV)e

EOx/Vf

SS PI1

302, *402

478

5.69

-2.88

2.81

1.29

 

38,090

 

 

 

 

 

SS PI2

325, 466

495

5.65

-3.26

2.39

1.25

 

38,200

 

 

 

 

 

SS PI3

305, 503

523

5.75

-3.48

2.27

1. 35

 

25,980

 

 

 

 

 

Table 1 Absorption, photoluminescence, electrochemical data and HOMO, LUMO energy levels of the synthesized dye

  1. aAbsorption spectra was measured in Dichloromethane solutions (1X10-5M) at rt, *weak absorption band
  2. bPhotoluminescence spectra is measured in N,N-Dimethylformamide solutions (1X10-6M)
  3. c,d EHOMO and ELUMO were calculated from the oxidation potential of the dyes and Eg
  4. EHOMO = - (EOx(onset) + 4.8 –EFC); ELUMO = EHOMO - Eg; where EFC is potential of internal standard ferrocene.
  5. fOxidation potential of the synthesized dyes (1mM) were obtained from cyclic voltammetry with 0.1M n-TBAPF6 as supporting electrolyte (scanning rate, 300 mV/s; working electrode and counter electrode, Pt electrode and Pt wire; reference electrode, Ag/AgCl) potentials measured vs Ag/AgCl were converted n to NHE by addition of 0.2 V
  6. eEg was estimated from the onset of absorption and photoluminescence spectra of the synthesized dye.

 

The absorption band of SS PI2 and SS PI3 with nitrophenyl acetonitrile and rhodanine acetic acid as an acceptor exhibits red shift about 35nm, compared to that of SS PI1 with cyanoacetic acid anchoring part and this shift is owing to that the nitrophenyl acetonitrile and rhodanine acetic acid units extend the π system of the ring via the nitrophenyl ring and 4-oxo-2-thioxothiazolidine ring.31 In comparison with SS PI2 and SS PI3, the molar extinction coefficient of SS PI1 is higher, which is an advantageous spectral property for light harvesting ability. However, the compound SS PI1 exhibits one strong absorption band in shorter wavelength and another one band in the visible region shows weak absorption band, because of the molecular structure of SS PI1 having lesser number of heteroatom as compared with SS PI2 and SS PI3. The two bands observed in the spectra is due to introducing imidazole derivative to the framework of phenothiazine core resulting of an improved light harvesting ability.32,33

Noticeably, the compounds SS PI1, SS PI2 and SSPI3 possess a broader absorption range (red shift) and higher molar extinction coefficients (38,090 M-1 cm-1, 38,200 M-1 cm-1 and 25,980 M-1 cm-1), which should be favorable for photocurrent generation in DSC’s because more photons can be harvested.1a Moreover, these molar extinction coefficients (ε) of the dyes are high compared with promising organometallic ruthenium dyes such as N3 (13900 M-1 cm-1) and N719 (14000 M-1cm-1).

The absorption spectra of dyes anchored on nanocrystalline TiO2 film are displayed in Figure 4. Though the absorption tailing for the dyes in dichloromethane solution is quite similar, it moved towards high energy in photoanode. Generally the dyes form aggregates at the surface of the TiO2. A red shift is witnessed when J-aggregates are predominant and the dye–TiO2 interaction is weak.34 On the contrary the formation of H aggregates at the TiO2 surface or stronger dye–TiO2 interactions causes a blue shift in the absorption profile.35,36 Noticeable wider and red shift for the synthesized dyes may be ascribed to the predominant dye–TiO2 interactions (deprotonation of carboxylic acid), as the substituted imidazole unit present in the donor part of the dye will inhibit the close intermolecular association of dyes at the surface of TiO2 better than the N–propyl chain. However, the longer alkyl chains could decrease the unfavorable aggregation on the TiO2 surface,37,38 which has been suggested accountable for greater DSC’s performances.

The emission spectra of the dyes recorded in dichloromethane solutions (Figure 5) are in similar in nature and the effect of peripheral units is not significant. This suggests that this excited state is ICT nature. Based on the intersection of absorption and emission spectra, the zeroth – zeroth transition energies (E0-E0) of the dyes SS PI1, SS PI2 and SS PI3 are estimated to be 2.81, 2.39 and 2.75 eV, respectively.

Figure 3 Absorption spectra of the synthesized dyes in CH2Cl2.

Figure 4 Absorption spectra of TiO2 films sensitized by SS PI1, SS PI2 and SS PI3.

Figure 5 Photoluminescence spectra of the synthesized dyes in CH2Cl2.

Electrochemical behavior

To evaluate the thermodynamic possibility of electron injection and sensitizer regeneration, cyclic voltamograms (Figure 6) recorded in N, N, - dimethyl formamide to determine the oxidation potentials (Table 1). The oxidation potential (Eox) correspond to HOMOs. as listed in Table 1., the HOMO level of dyes SS PI1, SS PI2 and SS PI3 were 5.69 V, 5.65 V and 5.75 V vs NHE respectively; these values are more negative than the I I-/I-3 redox potential value (0.4 V vs NHE), indicating that the oxidized dyes could be efficiently regenerated by the electrolyte.

The resulting E0-0 values were estimated from the onset of absorption and emission spectra of these dyes. The LUMOs were calculated from the values of Eox and the zero-zero band gaps (E0-0). As a result, the LUMO levels of dyes SS PI1, SS PI2 and SS PI3 are -2.88 V, -3.26 V and -3.48 V respectively, which are more negative than the conduction band (CB) edge of TiO2 (-0.5 V vs NHE), providing the thermodynamic feasibility of electron injection from the excited dye molecules into the CB of TiO2. According to a report in the literature, stronger electron donating ability of the donor group results in a higher HOMO energy level.27

The schematic energy levels of the dyes based on absorption and electrochemical data are shown in Figure 7. According to Figure 7 these dyes are considered to have proper electronic energy levels as promising sensitizers in DSC’s.

Figure 6 Cyclic voltamograms of the synthesized dyes dissolved in DMF with scan rate of 100mV/sec. Vs Ag/AgCl.

Figure 7 Schematic energy levels of synthesized dyes based on optical and electrochemical data.

Conclusion

In this work, we have designed and developed a new imidazole –phenothiazine based organic dyes namely SS PI1, S PI2 and SS PI3 and characterized by NMR and FT -IR spectroscopic analyses. Their optical and electrochemical properties were studied systematically. From the obtained results, we found that the auxiliary chromophores imidazole derivative plays an important role in light harvesting ability of the dyes via its extended π-conjugation. Likewise, the cyanoacetic acid acceptor moiety has unique structural features as compared with the other two anchoring units we used which have higher molar extinction coefficient and efficient binding ability on TiO2 surface. Based on the literature reports these phenothiazine core based dyes can achieve above 5 % efficiency and this contribution will pave a new way for further molecular design of sensitizers for efficient DSC’s.

Acknowledgements

S.S. thanks to University Grants Commission (UGC), Government of India for financial support through the UGB BSR fellowship (Ref. No. F. 4-1/2006 (BSR)/ 7-22/2007 (BSR) Dt. 26 June, 2012), Department of Science and Technology (DST), Science and Engineering Research Board (SERB), Government of India for International Travel Support (SB/ITS-Y/04782/2014-15, Dt. 30.12.2014) and Department of Science and Technology (DST), Fund for Improvement of S&T Infrastructure (FIST) for sanctioning DST FIST Program 2017 level ‘0’ (SR/FST/College – 111/2017; Dt. 16.01.2018).

Conclusion

The authors declare no competing financial interest.

Conflict of interest

Author declares that there is no conflict of interest.

References

  1. Nazeeruddin MK, Péchy P, Grätzel M. Efficient panchromatic sensitization of nanocrystallineTiO2 films by a black dye based on atrithiocyanato–ruthenium complex. Chem Comm. 1997;(18):1705‒1706.
  2. Mishra A, Fisher MK, Bӓuerle P. Metal-free organic dyes for dye-sensitized solar cells: from structure: property relationships to design rules. Angew Chem Int Engl. 2009;48(14):2474‒2499.
  3. Chen S, Xu XJ, Liu YQ, et al. Synthesis and Characterization of n‐Type Materials for Non‐Doped Organic Red‐Light‐Emitting Diodes. Adv Funct Mater. 2005;15(9):1541‒1546.
  4. Tsai YL, Chang CC, Kang CC, et al. Effect of different electronic properties on 9-aryl-substituted BMVC derivatives for new fluorescence probes. J Lumin. 2007;127(1):41‒47.
  5. Yoon KR, Ko SO, Lee SM, et al. Synthesis and characterization of carbazole derived nonlinear optical dyes. Dyes and Pigments. 2007;75(3):567‒573.
  6. Roquet S, Cravino A, Leriche P, et al. Triphenylamine−Thienylenevinylene Hybrid Systems with Internal Charge Transfer as Donor Materials for Heterojunction Solar Cells. J Am Chem Soc. 2006;128(10):3459‒3466.
  7. Marszalek M, Nagane S, Ichake A, et al. Tuning spectral properties of phenothiazine based donor–π–acceptor dyes for efficient dye-sensitized solar cells. J Mater Chem. 2012;22(3):889‒894.
  8. Velusamy M, Hsu YC, Lin JT, et al. 1-Alkyl-1H-imidazole-based dipolar organic compounds for dye-sensitized solar cells. Chem Asian J. 2010;5(1):87‒96.
  9. Hara k, Sayama k, Ohga Y, et al. Chem Commun. 2009;2198.
  10. Liang M, Wu W, Cai F, et al. New Triphenylamine-Based Organic Dyes for Efficient Dye-Sensitized Solar Cells. J Phys Chem C. 2007;111(11):4465‒4472.
  11. Koumura N, Wang ZS, Miyashita M, et al. Substituted carbazole dyes for efficient molecular photovoltaics: long electron lifetime and high open circuit voltage performance. J Mater Chem. 2009;19(27):4829‒4836.
  12. Tian H, Yang X, Chen R, et al. Phenothiazine derivatives for efficient organic dye-sensitized solar cells. Chem Commun. 2007;(36):3741‒3743.
  13. Wu W, Yang J, Hua J, et al. Efficient and stable dye-sensitized solar cells based on phenothiazine sensitizers with thiophene units. J Mater Chem. 2010;20(9):1772‒1779.
  14. Horiuchi T, Miura H, Sumioka K, et al. High efficiency of dye-sensitized solar cells based on metal-free indoline dyes. J Am Chem Soc. 2004;126(39):12218‒12219.
  15. Horiuchi T, Miura H, Uchida S. Highly-efficient metal-free organic dyes for dye-sensitized solar cells. Chem Commun. 2003;(24):3036‒3037.
  16. Satoh N, Nakashima T, Yamamoto K. Metal-Assembling Dendrimers with a Triarylamine Core and Their Application to a Dye-Sensitized Solar Cell. J Am Chem Soc. 2005;127(37):13030‒13038.
  17. Ning Z, Tian H. Triarylamine: a promising core unit for efficient photovoltaic materials. Chem Commun. 2009;(37):5483‒5495.
  18. Tang J, Hua J, Wu W, et al. New starburst sensitizer with carbazole antennas for efficient and stable dye-sensitized solar cells. Energy Environ Sci. 2010;3(11):1736‒1745.
  19. Teng C, Yang X, Li S, et al. Tuning the HOMO Energy Levels of Organic Dyes for Dye‐Sensitized Solar Cells Based on Br−/Br3− Electrolytes. Chem Eur J. 2010;16(44):13127‒13138.
  20. Nagarajan N, Vanitha G, Ananth DA, et al. Bioimaging, antibacterial and antifungal properties of imidazole-pyridine fluorophores: synthesis, characterization and solvatochromism. J Photochem Photobiol B. 2013;127:212‒222.
  21. Zhou L, Jia C, Wan Z, et al. Effect of imidazole derivatives in triphenylamine-based organic dyes for dye-sensitized solar cells. Organic Electronics. 2013;14(7):1755‒1762.
  22. Chen C, Liao JY, Chi Z, et al. Metal-free organic dyes derived from triphenylethylene for dye-sensitized solar cells: tuning of the performance by phenothiazine and carbazole. J Mater Chem. 2012;22(18):8994‒9005.
  23. Mao J, He N, Ning Z, et al. Angew Chem Int Ed. 2012;57;987.
  24. Cong J, Yang X, Liu J, et al. Nitro group as a new anchoring group for organic dyes in dye-sensitized solar cells. Chem Commun. 2012;48(53):6663‒6665.
  25. Yang CH, Lin WC, Wang TL, et al. Mater Chem Phys. 2011;130:635.
  26. Venkateswararao A, Justin Thomas KR, Lee CP, et al. Organic Dyes Containing Carbazole as Donor and π-Linker: Optical, Electrochemical, and Photovoltaic Properties. ACS App Mater Interfaces. 2014;6(4):2528–2539.
  27. Vijay Kumar C, Raptis D, Koukaras EN, et al. Study of an indoline–phenothiazine based organic dye for Dye-Sensitized Solar Cells. Theoretical calculations and experimental data. Organic Electronics. 2015;25:66‒73.
  28. Sirimanne PM, Tributsch H. Parameters determining efficiency and degradation of TiO2|dye|CuI solar cells. J Solid State Chem. 2004;177(6):1789‒1795.
  29. Hsin YC, Lung CH, Yuan CY, et al. Characteristics of triphenylamine-based dyes with multiple acceptors in application of dye-sensitized solar cells. J Power Sources. 2009;188(2):627‒634.
  30. Wan Z, Jia C, Duan Y, et al. Effects of different acceptors in phenothiazine-triphenylamine dyes on the optical, electrochemical, and photovoltaic properties. Dyes and Pigments. 2012;94(1):150‒155.
  31. Baheti A, Lee CH, Thomas KRJ, et al. Pyrene-based organic dyes with thiophene containing π-linkers for dye-sensitized solar cells: optical, electrochemical and theoretical investigations. Phys Chem Chem Phys. 2011;13(38):17210‒17221.
  32. Guo K, Yan K, Lu X, et al. Dithiafulvenyl Unit as a New Donor for High-Efficiency Dye-Sensitized Solar Cells: Synthesis and Demonstration of a Family of Metal-Free Organic Sensitizers. Org Lett. 2012;14(9):2214‒2217.
  33. Roquet S, Cravino A, Leriche P, et al. Triphenylamine−Thienylenevinylene Hybrid Systems with Internal Charge Transfer as Donor Materials for Heterojunction Solar Cells. J Am Chem Soc. 2006;128(10):3459‒3466.
  34. Xu W, Peng B, Chen J, et al. New Triphenylamine-Based Dyes for Dye-Sensitized Solar Cells. J Phys Chem C. 2008;112(3):874‒880.
  35. Paramaguru G, Aravindkumar C, Peng G, et al. Molecular Engineering of 2-Quinolinone Based Anchoring Groups for Dye-Sensitized Solar Cells. J Phys Chem C. 2014;118(30):16896‒16903.
  36. Baheti A, Singh P, Lee CP, et al. 2,7-Diaminofluorene-Based Organic Dyes for Dye-Sensitized Solar Cells: Effect of Auxiliary Donor on Optical and Electrochemical Properties. J Org Chem. 2011;76(12):4910‒4920.
  37. Liang M, Xu W, Cai F, et al. New Triphenylamine-Based Organic Dyes for Efficient Dye-Sensitized Solar Cells. J Phys Chem C. 2007;111(11):4465‒4472.
  38. Shi J, Chai Z, Su J, et al. New sensitizers bearing quinoxaline moieties as an auxiliary acceptor for dye-sensitized solar cells. Dyes and Pigments. 2013;98(3):405‒413.
Creative Commons Attribution License

©2018 Sambathkumara, et al. This is an open access article distributed under the terms of the, which permits unrestricted use, distribution, and build upon your work non-commercially.